Copyright © 2026 J and E Engineering Services Ltd All Rights Reserved

ENQUIRIES (+44) 1706 222662 01706 222662 Telephone Daimler Specific info@250v8.co.uk General Enquiries info@jandeengineering.co.uk

J and E Engineering Services Ltd.

Unit 32 Britannia Mill,

Stoneholme Road,

Crawshawbooth,

Rossendale,

Lancashire.

BB4 8BA.


Monday

Tuesday

Wednesday

Thursday

Friday

Saturday

Sunday

8:30am - 5:30pm

8:30am - 5:30pm

8:30am - 5:30pm

8:30am - 5:30pm

8:30am - 5:30pm

9:00am - 2:00pm

Closed

CONTACT INFORMATION OPENING HOURS VAT Number GB738470805 EORI Number GB738470805000 Company Number 16821373 Websites Main: www.jandeengineering.co.uk Main Alternative: www.j-and-e.co.uk Daimler V8: www.250v8.co.uk Daimler V8: Alternative: www.250v8.com
Home
Spark Plug Tubes

Oil within the spark plug tube is a common complaint. Up until recently the only way to cure this problem was to apply copious amounts of sealant the the threads as the standard copper washer seal is woefully insufficient. On this web page we will show you our modified sealing rings, modified tubes and specialist tooling to cure this problem once and for all without the need for sealant.

Our in-house machining capabilities have allowed us to design and manufacture a new revised sealing ring arrangement to help combat this age old problem. Our new seal uses two Viton rubber O’rings to seal directly against the spark plug tube and the cylinder head. This negates the use of any thread sealant and does not rely on the spark plug tube being over tightened which can damage the cylinder head and plug tube. The steel ring is reusable and is machined to accept O’rings which can be replaced when necessary.

Plug Tube Seal Manufacture Click to view the video.

The video here shows our Hurco CNC lathe in operation during the manufacture of the steel sealing rings. Fully automated including bar feed and auto parts catching. Once collected from the basket a quick de-burr, QC check and fit the two sealing rings. Job done!.

Click the PLAY button to view the video.

The images above show the CAD/CAM drawing, Automatic tool changer, auto chuck and tube being held in the chuck. On the right are a batch of new sealing rings complete with O’ring seals.

Plug tubes and cylinder head spot facing must be in good condition and free from excessive corrosion in order for the rubber O’rings to achieve a good seal. A slight taper at the bottom of the plug tube may be required in order for the O’ring to slide into the tube. Sealant, grease or oil can be used to assist fitting. We recommend a slight smear Wellseal in most cases.

Oil leaks from the sparkplug tubes are very common with the V8. Originally sealed by a “Z”-profile copper crush washer as the tube is screwed into the cylinder head. Over time and after being subject to multiple heat cycles the copper seal will fail and cause the spark plug tube to fill with oil, which can affect spark plug efficiency due to contamination and potential misfire. Fumes are then emitted as the engine runs, due to these oil leaks, which can cause a very real risk of fire!




The images above demonstrate just how poor fitting the copper washer is against the spark plug tube. This is why people feel it necessary to use excessive amounts of sealant around the threads when installing the plug tubes. This in itself can cause additional engine troubles as the sealant can become detached and block small oil passages and pickup pipes. This of course must be avoided. This practice also makes the removal of the plug tubes difficult and very messy should you need to as the sealant clogs the threads in the hole and on the tube.


In theory the cure for this oil leaking problem is to simply replace the copper seal from time to time. The reality however is far from simple. The plug tube is made from steel and the cylinder head is alloy which over time ensures the two are bonded quite firmly. Breaking this bond can be difficult as you cannot really get hold of the thin, smooth wall plug tube without causing deformation and damage. You will also find that the copper crush washers are small in the outer diameter so as not to get stuck inside the cylinder head when crushed. This leads to the problem of the copper washer slipping to the bottom of the hole in the cylinder head when replacing the tubes in-situ because of the “V” engine layout. The images below show how little surface area of the copper seal contacts the plug tube. This is why so many people suffer continued oil leaks even after replacing the copper sealing washers.

Modified Sealing Ring Modified Plug Tube Solution 2 Solution 1

If your spark plug tubes are corroded or have been damaged in the past we now offer brand new replacements. These are CNC machined from CDS tube with original dimensions and thread sizes. We have also included an integral modified sealing end in order to eliminate those pesky oil leaks in the same way our modified sealing ring works. Brand new plug tubes are available singular or in sets of eight.

Integral Seal. Special Tooling Plug Tube Removal & Install

This is our plug tube removal and install tool. Plug tubes can be really tough to remove and most people have to resort to a pipe wrench or stilsons to get them out. This method can damage and distort the thin wall tube and make a real mess of things. Our removal tool slides inside the plug tube and grips from within using an expanding sleeve and taper. As it does not attach or clamp to to the fragile threads of the tube it cannot damage them like other tools available.  This tool can be used with the cylinder heads on the bench or in situ under the bonnet without causing any damage to the plug tube.

All of our specialist tooling and modified seal kits are available to order. Please call or E-mail for more information.

Our Rocker cover nut puck is designed to allow for the easy removal and install of the rocker cover hand nut. It is made from a light weight but strong plastic and features a 1/2” square drive so that it can be used with a ratchet or T-bar. The puck will not damage the aluminium rocker cover or hand nut. The use of the puck negates the need for a large pair of grips or hammer in order to tighten or remove the nuts. Here they can be seen in yellow to aid photographic representation, all currently supplied nut-puck spanners are supplied in black. Do NOT over tighten the rocker cover nuts.

Rocker Cover Nut ‘Puck’ WITH NEW Price Reduced to celebrate the  launch of  www.250V8.co.uk Now only £29.00 + P&P £29.00 Special Price