Copyright © 2026 J and E Engineering Services Ltd All Rights Reserved

ENQUIRIES (+44) 1706 222662 01706 222662 Telephone Daimler Specific info@250v8.co.uk General Enquiries info@jandeengineering.co.uk

J and E Engineering Services Ltd.

Unit 32 Britannia Mill,

Stoneholme Road,

Crawshawbooth,

Rossendale,

Lancashire.

BB4 8BA.


Monday

Tuesday

Wednesday

Thursday

Friday

Saturday

Sunday

8:30am - 5:30pm

8:30am - 5:30pm

8:30am - 5:30pm

8:30am - 5:30pm

8:30am - 5:30pm

9:00am - 2:00pm

Closed

CONTACT INFORMATION OPENING HOURS VAT Number GB738470805 EORI Number GB738470805000 Company Number 16821373 Websites Main: www.jandeengineering.co.uk Main Alternative: www.j-and-e.co.uk Daimler V8: www.250v8.co.uk Daimler V8: Alternative: www.250v8.com
Home

This Daimler SP250 was taken to the B.E.L Motors, workshop in Lancashire for a job to stop engine oil leaking into the spark plug tubes. The owner and DLOC member supplied our modified seal kit to the garage and this case study shows how they got on.

The common problem of oil leaking into the spark plug tubes has plagued this particular Daimler SP250 for many years. The copper washers had been replaced many times but to no avail. It was time to try a new approach. The modified spark plug tube sealing kit from J & E Engineering Services was purchased along with associated tooling to aid fitment. This consisted of a rocker cover nut spanner and tube removal and install tool. First job was to remove the air cleaners, breather pipes and ignition leads.

This is the rocker cover nut spanner “Puck” which was used for undoing the rocker cover hand nuts. It has a square drive so that it can be used with a ratchet or in our case, T’Bar. It is made from hard plastic and did the job easily.

Once the rocker covers were removed and with the aid of a torch we could see the engine oil around each of the spark plugs. All eight showed this problem with a decent amount of oil in each. We couldn't clean out the oil properly with the spark plug and tube fitted and we didn’t want to drop the oil into the cylinder by removing the spark plug at this stage. We decided we would try and remove the tube first leaving the spark plug in place. This is where the second tool came in. The spark plug tube removal and install tool. A hefty piece of kit that expands inside the tube with the use of a taper and lock nut. We weren’t able to slide the tool fully into the tube because we had left the spark plug installed, but we thought we would give it a go. These tubes were tight and some hade been fitted with additional sealant but the tool worked faultlessly and made what initially looked like a daunting job very easy.

With the tubes removed we could see the old copper washer which hardly seemed man enough for this job and it didn't fit the bottom of the tube particularly well either. No wonder these things leak.

With the tubes removed we could remove the oil with the aid of a suction tool prior to removing the spark plug. This prevented dropping the oil or any debris into the cylinder. A final clean up of the seating face and cleaning of the tubes we were ready to re-fit. Below you can see the freshly prepared tube and new sealing ring with twin o-rings. A slight smear of “WellSeal” or engine oil helps lubricate the rubber seals much like the sealing ring when fitting an oil filter. The ring snaps into the tube with a satisfying “Click”. A bit of lube on the threads and we were ready to screw them back in.

The removal/install tool was used to fit the tubes back into the cylinder head and again proved invaluable. We were able tighten the tubes nice and snug without any fuss. Rocker cover gaskets were replaced along with new O-ring seals under the retaining nuts and a new set of plugs. A quick “spit and polish” of the covers prior to fitting brightened things up under the bonnet. In conclusion, a straight forward job in theory, made easy by having the correct tools. Quite an enjoyable few hours work. Job Done.

William Brewston B.E.L Motors

More information about our modified sealing kits and specialist tools detailed in this article can be found on the dedicated web page via the navigation bar or by clicking this button.

Introduction Lets Begin Spark Plug Tubes