Here you will find some of the dedicated engine building tools we manufacture and some of the specialist parts and modifications specifically for the Daimler V8 engine owner.
D.505 Crankshaft rear oil seal pre-sizing & Centralising tool. Uses the line bore rear main to ensure proper centralisation required for correct fitment of the rear crankshaft oil seal packing for all V8 & 250 Saloon engines as well as some very late production SP250. Available for outright sale or hire.
Oil Pump Alignment Tool. This tool allows for the correct alignment of the oil pump when assembling your engine. This can be seen in the workshop manual although has no special tool designation. The alignment of the oil pump is very important and prevents drive shaft binding in the upper and lower bushes. Incorrect alignment will load the drive shaft which can accelerate wear in the drive gear, bushes and oil pump. Supplied with sliding T-handle.
Crankshaft Rear Oil Seal Packing. C22996. This is the correct seal for all saloon models and very late SP250 cars. They are of the correct material and correct length to maximise achieving a good seal. Graphite impregnated. Should be used with oil seal pre-sizing & centralising tool D.505.
Daimler V8 Crankshaft Rear Oil Sealing Rings. 431242. To suit SP250-Dart & Majestic Major 4.5. Complete with precision ground offset scarf joint as per original specification. Supplied in single rings or pairs as required. One standard thickness of 2mm grade C. Can be ground thinner if required at additional cost. Thicker rings also available on a made to order basis if required.
Crankshaft Protector Rod Bolt Boots. This simple pair of rubber boots slides on to the connecting rod bolts when installing the pistons. They protect the crankshaft journals from contact damage when pushing in the piston assembly from the top. Made from soft plastic. Sold in pairs. Suitable for other engines.
Sludge Plug Removal Tool. May look like a modern torx bit but it is not. It is a new special design bit for the removal of female hex plugs as fitted to the Daimler V8 crankshaft sludge traps. We use this tool in our own workshop with great results. 3/8” drive Can be used with an impact wrench. Imperial size correct for the plug. Made in U.S.A.
Crankshaft Rear Oil Seal Modification Kit. This rear oil seal conversion is suitable for both saloon and SP250-Dart engines. It supercedes the rope packing type and dual ring seal arrangements by using a complete 360° FKM rubber oil seal. Comes with billet alloy housing and all fixings. Requires some additional engineering and machining processes. Only available as part of a full engine re-build or full engine machining order in the UK. Available to overseas customers in kit form subject to approval.
Replacement Crankshaft Rear Oil Seal. Replacement oil seal to suit our rear oil seal conversion kit. To suit both saloon and SP250 kits. FKM Fluro-Rubber good for 7500+ rpm.
FKM/ Viton Fluro Sponge Cord Sump Pan End Seals. 308402 / 308470. Seals fit around the rear main bearing cap and front alloy bridge piece, sealing the sump pan to the cylinder block. The best material available for this job. Correct size, hardness (30 Shore A), temperature stability & resistance to oils & fuels. Outperforms nitrile & silicone products by a country mile. Supplied as two seal lengths that require trimming to suit your engine. Included as standard in our gasket sets
Daimler V8 Timing Cover Oil Seal Modification. A re-worked timing cover using a modern double lip oil seal. A new central, internal boss tig-brazed & machined. Supplied blasted bare metal ready to paint. Includes modification to crankshaft damper hub. Sold on an exchange or outright sale basis.
Oil Pressure Priming Tool. This tool is inserted through the cylinder block and into the oil pump. It accommodates the use of an electric drill or wrench to turn the oil pump and generate oil pressure prior to starting your freshly rebuilt engine. Oil pressure can be seen on your, in-car oil pressure gauge or remote gauge set up. Can also be used for oil pump alignment during assembly and to orientate the oil pump rotor when installing your distributor drive spindle. Universal design ensures use for SP250, Saloon and Majestic Major V8 units & all oil pump gear types.
SP250 Spin-on Oil Filter Kit. Upgrade kit which allows the fitment of a modern spin on oil filter canister. No more paper elements and messy oil changes with this kit. Supplied with a genuine “Mann” oil filter. The best quality available.
V8 Saloon Spin-on Oil Filter Kit. Upgrade kit which allows the fitment of a modern spin on oil filter canister. No more paper elements and messy oil changes with this kit. Supplied with a genuine “Mann” oil filter. The best quality available.
Replacement filter canisters Available separately in the “Engine Service” Section
Modified Oil Pressure Relief Valve Kit. C22756 MOD. This kit includes a modified relief valve that will add around 6-8lb of pressure at higher rpm. A new standard spring and locking tab are also included. A sensible modification for all re-builds.
Fully Rebuilt Uprated Oil Pump Assembly. Saloon, SP250, Majestic Major. C.22490 / C21975 / 431567. A fully rebuilt oil pump uprated to exceed original specifications. Fully inspected tolerance checked, re-machined and ultrasonically cleaned. Fitted with our uprated pressure relief valve & spring kit (Seen above). Tested primed & ready to fit.
Crankshaft Sludge Trap Plug set.C22796. Replacement set of four sludge trap blanking plugs. Correct length size & thread. Secured with modern thread lock & staking once you have cleaned out the sludge.
Heavy Duty Easy Tighten Oil Pump Mounting Bolt Kit. Access around the oil pump in order to tighten correctly has always been difficult as the original head size of the bolt is too big. This kit utilises a double hex design of small diameter which means you can use a standard 3/8” ring spanner rather than the 1/2” open ended required previously. An integral flange allows for correct load spread on the pump casting. Used without locking tab washers.
Oil Gallery Blanking Plug For SP250 and Saloon Blocks. C22660. These plugs are used for the main oil gallery that runs the entire length of the block, one at each end. Early SP250 blocks used aluminium bungs without means of removal so they must be drilled out. This is essential if you wish to clean out the oil gallery during a re-build. Sold as a set of two plugs
ARP Heavy Duty Main Bearing Cap Bolt Kit. 430420. Used to replace your 60+ year old main cap bolts. Kit contains 12 bolts including the two short bolts for the outside rear main cap. Includes heavy duty, internal chamfer washers to prevent head “pop-off”. For use with standard main caps or available for use with our main cap strap kit. Do not require locking tabs/tab washers to be used. Essential for any Daimler V8 re-build. Best quality available.
Heavy Duty Connecting Rod Bolt & Nut Set. Set of 16 heavy duty big end bearing cap bolts and nuts to replace your 60-year old fittings. Essential for any Daimler V8 engine re-build. Supplied with fitting instructions and an updated tightening torque figure setting.
£160.00 8-Cylinder Set
Connecting Rods Not Included
New Big End Bearing Cap Nut Set. 430424. Original Jaguar supply & latest specification. 3/8 UNF 12-point nut with flange. Complete as a set of 16 nuts. Best quality available. NOT aftermarket Junk.
Heavy Duty Tri-Metal Big End Bearing Set. Set of big end bearing shells in heavy duty tri-metal material. Available in STD, +.010”, +.020”, +.030”, +.040” under-sizes.
£85.00 Set
Heavy Duty Tri-Metal Main Bearing Set. Set of main bearing shells in heavy duty tri-metal material Available in STD, +.010”, +.020”, +.040” under-sizes.
£89.00 Set
£15.00
Uprated Standard size & Oversize Thrust Washer Set. 307680. Set of oversize thrust washers for setting crankshaft end float. Available in STD, +.005” , +.010”. These washers come in pairs as original. Also available in sets of three washers to suit thrust washer modification machined cylinder blocks.
£22.00 Set of two
£28.00 Set of three
Intermediate Main Bearing Cap Strap Kit. This strap kit will strengthen and stiffen-up the main bearing caps which can sometimes fracture and break. Your main bearing caps will require a simple machining operation in order to fit this kit. Strap kit is supplied complete with a full set of ARP extended length main bearing cap bolts and heavy duty chamfered washers. We can machine your main bearing caps to suit this modification if required. An essential modification for all block castings.
Heavy Duty 4-Bolt Intermediate Splayed Main Bearing Cap Set. The ultimate in stiffening up the crank area of the Daimler V8. Set contains 3x bespoke Four bolt splayed semi-finished main bearing caps & full set of ARP fixings. Will require extensive cylinder block machining & line boring to complete. If your block has broken the original main bearing caps this may be a repair option for you. This is one step up from our main bearing cap strap kit. Only available as special order set.
Repair Sleeve Cylinder Liner. Spun cast iron cylinder liner used to repair damagedcylinders or recovera cylinder block back to standard size. Interference fit. Machining required. Available as individual items or set of eight liners.
Oil Pump Drive Spindle. Early: 430362 / Late: C.20971 Available for SP250 and Saloon please state. Precision ground and CNC machined to original specification. Used to replace bent, damaged or worn drive shafts. Complete with keyway ready to accept key & drive gear
Oil Pump Drive Shaft Bush (Top). 422583 / C23331. A CNC machined replacement top bush for the oil pump/distributor drive shaft. Fits into the cylinder block with an interference fit. Choice of two available: Semi-finished will require line reaming/boring once fitted as indicated in the workshop manual or fully finished already bored to shaft size. Easier to fit but alignment should be checked.
Front Bridge, Cap Head Screw Kit. 425938 MOD. This screw kit replaces the old slotted hex screws originally fitted. They retain the front alloy hoop over the front main bearing cap to the cylinder block. The allen cap head allows for correct and easy tightening and removal of the hooped casting. Supplied with two lock washers. (Alloy Bridge not included)
Modified Oil Pick-up for SP250 Specification V8 430354: A replacement option if your pick-up has been damaged or fallen apart. Our modified part features a baffle and lens to ensure the most constant oil pickup focused directly into the pump as used in modern engines. The screen gauze is also the correct industry standard gauge to help prevent foreign bodies (Or flakes of red paint!) From entering the pump. The pump face is precision ground flat to remove wear, ensure a good seal and minimise pressure loss. Sold on an exchange basis. You can supply either a saloon or SP250 unit for exchange. Supplied with new fixings.
Crankshaft Spigot Bush / Pilot Bearing All Variants C.2226, 1216/14, : Oilite pilot bushes for rear of crankshaft to suit manual / auto variants.
Fuel overflow pipe clip set. 431354. These pipe clips are fitted around the timing cover and allow the fuel overflow pipes from the carburettors to be secured to the cylinder block. Supplied as a set of 4 clips in bright zinc plating (BZP), for corrosion resistance.
Modified & Ground Anti-Pump Cam-follower. 430388 MOD. A restoration and modification for your camshaft follower. A full re-profile ground base circle, cross drilling to eliminate lifter fill & hydraulic action and a re-crimp of the top tube to hold the ball end tight and secure as it should be. Vapour blasted & supplied ready to fit. Indicated price is to refurbish one of your camshaft followers in this manner. This modification is carried out on all our full re-builds and considered an essential modification. More information available on request.
Timing Sprocket Set. 307925 / 307339. Includes both camshaft and crankshaft timing sprockets. To replace damaged, chipped or broken sprockets. Only available as a special order set.
Heavy Duty Hydraulic Timing Chain Tensioner Kit. This is our Heavy-Duty billet alloy timing chain tensioner with nylon rubbing pad as fitted to modern engines. Comes complete with anti-bleed-back valve, gasket & bolts. The ultimate in chain tension control & reliability. No rubber pad to de-laminate or slip here.
£199.00 kit
Heavy Duty German Timing Chain with New Modified Chain Damper. 307920 MOD / 307363. Endless (No split-link) timing chain of the highest quality for use with standard tensioner or our heavy duty hydraulic tensioner. As used in all our full engine rebuilds. Made in Germany not India.
Includes our new & modified timing chain damper to replace the 60+ year old moulded type. We have seen these crack, deform & break up filling the sump with small pieces of plastic. Ours allows for slight adjustment so you can set it just right. Bespoke Made from billet Ertalon (Stanyl®) as used in modern engines.
£120.00
Ultimate Heavy Duty Timing Chain Full Kit. Includes hydraulic timing chain tensioner, heavy duty timing German timing chain & our new billet timing chain damper (307920) as seen above. Comes complete with fixings. Doesn't get any better than this. A nice addition to our modified timing cover & damper damper hub with oil seal conversion.
£299.00
Heavy Duty Timing Chain. 307363. Endless (No split-link) timing chain of the highest quality for use with standard tensioner or our heavy duty hydraulic tensioner. As used in all our full engine rebuilds. Made in Germany not India.
£60.00
Crankshaft Rear Split Seal Conversion, Replacement Seal.This seal is required if your cylinder block and crankshaft has been previously modified to suit a split type rear oil seal. Although we don't like this ill conceived modification as it is a poor solution and it is not one that we carry out. Your block and crankshaft may have been compromised in this irreversible manner. At least we can supply a suitable seal if this is the case with your engine. This seal is CNC precision wafer cut and hinge cut on the opposing side. This allows for easy fitment and reduced seal distortion during fitting. Complete with garter spring.
If you wish to place an order for any of our parts, tools or consumables please send an email to: info@250v8.co.uk Please include your full name, shipping address, contact telephone number and of course the items you would like to order. We will raise a free, no-obligation quotation by return email which will include payment instructions should you wish to proceed with the order. Once paid your items will be shipped as detailed in the quotation.
All prices indicated are correct at time of publication however they may be subject to change without prior notice. All prices are trade price. All parts and tools available over our trade counter or to mail order. Domestic and international shipping and packaging available at additional cost and subject to import duties & local taxes. Thank you for taking the time to look at our Daimler V8 products and tools.
New Flywheel Bolt Set For SP250 And Saloon Manual Transmission Cars. 430465. Set of six bespoke flywheel dowel bolts for manual transmission cars as per original length design and specification. The use of automatic drive plate bolts to retain a flywheel to the crankshaft is incorrect and dangerous as they are too short and at risk of shear or thread damage.
£85.00 Six Bolt Set
Brand New Flywheel to Suit SP250 And Saloon: 307407 SP250 / C.27426 Saloon: A brand new flywheel fully machined from billet to original specification and weight to suit Daimler SP250 Dart and V8 Saloons with manual transmission. With separate ring gear to make future replacement easy if required (Saloon only). Supplied fully balanced ready to fit. Includes clutch dowels. Machined with integral trigger wheel on the inside for electronic ignition and petrol injection systems.
£P.O.A. State which required
2-3 Weeks Delivery
Brand New 3-Piece 8½ Clutch Kit for Manual V8 Saloons & Jaguar 240: C27427 / C.23252 / C.23251. Brand new diaphragm spring clutch kit, not reconditioned or exchange. Available outright. Heavy duty version with optimised friction material contact & thickness friction disc. Supplied with brand new carbon clutch release bearing & clips.
£360.00.
Brand New Coolant Flanges for Water Pump & Water Outlet Positions 432237: New flanges to replace corroded or leaking items. Supplied with gasket and fittings. Our flanges have a swaged end to help prevent hose coming off, the same as original Daimler specification. Sold individually or in pairs. Supplied bare metal finish.
£18.00 Each
£34.00 Pair
Water Pump Rebuild Kit for Saloon & SP250: Highest quality water pump rebuild kit including 8-vane impeller, bearing with correct pulley shaft size of 0.6288”, bearing lock screw & mechanical seal. Kit also includes a seal press tool to help installation.
Water Pump / Alternator Drive Pulley Wheel Steel C.27434: BilletSteel double V' pulley wheel for alternator equipped saloon cars. Lighter and stronger than other available pulleys, dynamically balanced, with correct threaded holes and precision honed pilot bore.
Water Pump / Alternator Drive Pulley Wheel Aluminium C.27434: Billet 6000 series aluminium double V' pulley wheel for alternator equipped saloon cars. The lightest pulley wheel currently available for these cars. Total mass of around 766 grams 1.6kg lighter than steel equivalents, dynamically balanced, with correct threaded holes and precision honed pilot bore.
Water Pump Pulley Wheel Aluminium 307558: Billet 6000 series aluminium single V' pulley wheel for Daimler SP250 ‘Dart’ cars. The lightest pulley wheel currently available for these cars. Dynamically balanced, with precision honed pilot bore. Machined with threaded holes to allow the use of our special pulley removal tool available separately.
£200.00 SP250
Brand New Water Pump SP250 307845: New for 2026, brand new water pump assembly 307845 for SP250 ‘Dart’. Long time obsolete this item is now back at long last. Complete assembly, with stainless steel 8-vane impeller and ‘Feather light’ 6000 series alloy pulley wheel. Fully designed, machined, and assembled in our own workshop. Built to exceed original specification. Currently undergoing extensive performance and durability testing this item is due to be released Q1 2026. Watch this space for more information, log your interest or pre-order your pump by sending us an email to info@250v8.co.uk
£Enquire. SP250
Standard Timing Chain Tensioner 430426 / C.10332. This is standard specification original equipment timing chain tensioner not a reproduction part. Made in France this is a high quality item with correctly bonded full footprint rubber slipper and correct size oil feed hole spigot & gasket.
Do NOT mistake this item for the ‘Rolon’ tensioners manufactured in India which have a reputation for failure.