Copyright © 2026 J and E Engineering Services Ltd All Rights Reserved
J and E Engineering Services Ltd.
Unit 32 Britannia Mill,
Stoneholme Road,
Crawshawbooth,
Rossendale,
Lancashire.
BB4 8BA.
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
8:30am - 5:30pm
8:30am - 5:30pm
8:30am - 5:30pm
8:30am - 5:30pm
8:30am - 5:30pm
9:00am - 2:00pm
Closed
Home
Contact
Top End
Bottom End
Parts & Tooling
Gallery
Technical
T's & C's
The information on this sheet is for reference only. All weight, measurement and capacity figures are approximate. The details listed may be incorrect. You should not rely upon the information as a basis for making any business, legal or any other decisions.
STD Bore: 3.000” / 76.2mm
Stroke: 2.75” / 69.85mm
Compression Ratio: 8.2:1 (Std)
Compression Pressure: 120 psi (Approximate)
Bore Size for Liner: 3.149” - 3.150”
Piston to Bore Clearance: .0025” - .004”
Camshaft housing bore size: 1.5622” – 1.5633” / 39.68mm-39.71mm
STD Main Bearing Journal: 1.9995” – 2.000”
STD Big End Journal: 1.7490” – 1.7495”
Crank End Float: .003” - .007”
Valve Clearance: Inlet .011” Exhaust .014”
Spark Plug Type & Gap: BP6ES / 0.25”
Ignition timing: 9° BTDC
Main Bearing Cap Torque: 30 – 35 lb/ft (Standard fittings)
Connecting Rod Torque: 25 – 30 lb/ft (Standard fittings)
Cylinder Head: 55 – 60 lb/ft 4-stage (SLS Gasket. All 2.5 models. See below)
Camshaft Nut: 65 lb/ft (With thread lock)
Timing Chain Tensioner: 10 lb/ft (With thread lock)
Timing Chain Damper: 8 lb/ft (With thread lock)
Tappet Chest: 21 lb/ft
Sump: 21 lb/ft
Flywheel / Torque Plate: 43 - 48 lb/ft
Spark Plugs: 18 - 22 lb/ft
Tightening torque:
Stage 1: 20 lb/ft
Stage 2: 40 lb/ft
Stage 3: 60 lb/ft
Stage 4: Slacken 90° then tighten to 60 lb/ft. Repeat in order.
Specification
Firing Order
Tightening Torques
Oil Capacity
Crankshaft Machining
Flywheel
Fittings
Dimensions & Weight
Valve Springs
Water Pump
Oil Pressure
Crankshaft Balancing
Specification
Firing Order
Tightening Torques
Oil Capacity
Crankshaft Machining
Flywheel
Fittings
Dimensions & Weight
Valve Springs
Water Pump
Oil Pressure
Crankshaft Balancing
Inlet .011” Exhaust .014”
Daimler V8 2.5 full engine.
With: Intake manifold, sump, cylinder heads, rocker covers, flex plate. Damper & pulley.
Without: Carburettors, rotating electrics, flywheel, clutch, exhaust manifolds
Dry Weight: 175 kg
L= 670mm 26.5"
W= 650mm 25.5"
H= 630mm 24.75"
Daimler V8 2.5 Cylinder Head (Single).
With: Spark plug tubes, valves & springs installed.
Without: Spark plugs, manifold studs.
Weight: 10.4 kg
L= 450mm 17.75"
W= 210mm 8.25"
H= 165mm 6.5"
Daimler V8 2.5 Cylinder Block.
Bare, with mains caps & bolts.
Weight: 61.5 kg
L= 480mm 19"
W= 395mm 15.5"
H= 293mm 11.5"
Daimler V8 2.5 Crankshaft.
Weight: 16.6 kg
L= 640mm 25.25"
W= 150mm 5.9"
H= 150mm 5.9"
Standard Spring: Seat pressure: 55 lb. +/- 5lb
Full lift pressure: 118 lb. +/- 5lb
Installed height: 33.27mm
Bind Height: 23.7mm
engine refill amount: 6.8 litres
Engine refill from dry amount: 8 litres approx
engine refill amount: 6.82 litres.
Engine refill from dry amount: 8.1 litres approx
Measured from the alloy housing gasket face to the centre of the first ‘V’
Saloon: 36mm
SP250: 48.2mm
100% Rotating Mass + 50% Reciprocating Mass
50%
15g x1
Calculation:
Balance Factor:
Oil Allowance:
Saloon: 9.9kg
SP250: 9.9kg
Saloon: 104
SP250: 96
Saloon: 12.7mm
SP250: 12.7mm
Auto Flex Plate includes Washers: 9.5mm
Saloon: 7/16 UNF x 1
SP250: 7/16 UNF x 1
Auto Flex Plate: 7/16 UNF x 7/8”
SP250 & Saloon: Hot running: 35/45 psi
Hot Idling: 15 psi
Minimums: 10 psi per thousand RPM
Intake manifold set screw 5/16 UNC X 1 1/4 Q16
Thermostat housing set screw 5/16 UNC X 7/8 Q2
Water housing to cylinder head 5/16 UNC X 1 Q4
Water manifold to water pump 1/4 UNC X 7/8 Q2
Water housing to cylinder block 5/16 UNC X 1 Q4
Water blanking plate rear of each head 5/16 UNC x 3/4 Q4
Oil blanking plug front of each head 5/16 UNC x 1/2 or 7/8 Q4 with sealing washer
Belt tensioner to water housing 3/8 UNC X 1 Q2
Small water pump pipe take off ¼ UNC X 3/4 Q4
Back plate to cylinder block 5/16 UNC X 7/8 Q4
Engine mount to cylinder block 3/8 UNC X 3/4 Q8
Tappet Chest 5/16 UNC X 1 1/4 Q2 & 5/16 UNC X 7/8 Q9 (Centre bolts 1/4 UNC x 1 Q2)
Timing cover 1/4 UNC X 5/8 Q10 1/4 UNC X 7/8 Q2 for timing pointer. All with copper washers only
Camshaft lock plate 5/16 UNC X 5/8 Q2
Timing chain damper 1/4 UNC 3/4 Q2
Timing chain tensioner 1/4 UNC X 1 3/8 Q2 Bolt
Sump 5/16 UNC X 7/8 Q 16
Baffle 1/4 UNC X 1/2 Q5 for SP250 Q6 for saloon.
Oil filter head 5/16 UNC x1 Q4
Front Bridge 5/16 UNC 1 1/8 Q2
Oil pump mounting 5/16 UNC x 3/4 Q3
Specifications taken from a very late production Saloon motor.
Some specifications may differ depending on year and production date.
Main Bearing Journal Sizes:
Standard: 1.9995” – 2.0000”
+.010”: 1.9895” – 1.9900”
+.020”: 1.9795” – 1.9800”
+.030”: 1.9695 – 1.9700”
+.040”: 1.9595 – 1.9600”
Big End Journal Bearing Journal Sizes:
Standard: 1.7490” – 1.7495”
+.010”: 1.7390” – 1.7395”
+.020”: 1.7290” – 1.7295”
+.030”: 1.7190” – 1.7195”
+.040”: 1.7090” – 1.7095”
Crankshaft End Float:
Case Studies
Image Gallery