Copyright © 2026 J and E Engineering Services Ltd All Rights Reserved

ENQUIRIES (+44) 1706 222662 01706 222662 Telephone Daimler Specific info@250v8.co.uk General Enquiries info@jandeengineering.co.uk

J and E Engineering Services Ltd.

Unit 32 Britannia Mill,

Stoneholme Road,

Crawshawbooth,

Rossendale,

Lancashire.

BB4 8BA.


Monday

Tuesday

Wednesday

Thursday

Friday

Saturday

Sunday

8:30am - 5:30pm

8:30am - 5:30pm

8:30am - 5:30pm

8:30am - 5:30pm

8:30am - 5:30pm

9:00am - 2:00pm

Closed

CONTACT INFORMATION OPENING HOURS VAT Number GB738470805 EORI Number GB738470805000 Company Number 16821373 Websites Main: www.jandeengineering.co.uk Main Alternative: www.j-and-e.co.uk Daimler V8: www.250v8.co.uk Daimler V8: Alternative: www.250v8.com
Home

Spark Plug Tube Removal and Install Tool. D.506. Churchill designation. This tool is a much improved version of the Churchill design. It allows for simple removal and re-fitting of the cylinder head spark plug tubes without damaging or deforming them. Plug tube removal is required when replacing the seal at the bottom of the tube to prevent oil leaking. Used in conjunction with our modified sealing ring kits or complete tube with integral sealing end. Available for outright purchase or hire.

£170.00

Rocker cover nut “Puck”. To aid removal and tightening of the rocker cover hand nuts. Can be used by hand or 1/2” ratchet/T-bar thanks to the square drive hole in the centre. Shown here in yellow to aid photographic representation all pucks are supplied in black. Made from polyoxymethylene engineering plastic from Mitsubishi Industries.

Rocker Arm Adjusting Screw Spanner/ Tappet Adjusting Spanner. An essential tool for your tool kit. This double open ended spanner is the correct imperial size for the square rocker arm adjusting screws. Adjusting the valve clearances is difficult enough and this simple little tool makes life a little easier. Offset crank at one end and straight on the other . For all V8 Saloon and SP250 cars.

£20.00 each

Here you will find some of the dedicated engine building tools we manufacture and some of the specialist parts and modifications specifically for the Daimler V8 engine owner.

Special Tools, Modifications & Parts Daimler V8 Special Tools Press to Select Cylinder Head Parts Gaskets & Sealing Press to Select Cylinder Block Parts Press to Select Engine Service Press to Select Price Reduced to celebrate the  launch of  www.250V8.co.uk Now only £29.00 + P&P £29.00 Special Price Info Info

D.505 Crankshaft rear oil seal pre-sizing & Centralising tool. Uses the line bore rear main to ensure proper centralisation required for correct fitment of the rear crankshaft oil seal packing for all V8 & 250 Saloon engines as well as some very late production SP250. Available for outright sale or hire.

£250.00 Info

Oil Pump Alignment Tool. This tool allows for the correct alignment of the oil pump when assembling your engine. This can be seen in the workshop manual although has no special tool designation. The alignment of the oil pump is very important and prevents drive shaft binding in the upper and lower bushes. Incorrect alignment will load the drive shaft which can accelerate wear in the drive gear, bushes and oil pump. Supplied with sliding T-handle.

£55.00

Sludge Plug Removal Tool for V8. May look like a modern torx bit but it is not. It is a new special design bit for the removal of female hex plugs as fitted to the Daimler V8 crankshaft sludge traps. We use this tool in our own workshop with great results. 3/8” drive Can be used with an impact wrench. Imperial size correct for the plug. Made in U.S.A.

£29.00 each

Oil Pressure Priming Tool. This tool is inserted through the cylinder block and into the oil pump. It accommodates the use of an electric drill  or wrench to turn the oil pump and generate oil pressure prior to starting your freshly rebuilt engine. Oil pressure can be seen on your in car oil pressure gauge or remote gauge set up. Can also be used for oil pump alignment during assembly and to orientate the oil pump rotor when installing your distributor drive spindle. Universal design ensures use for SP250, Saloon and Majestic Major V8 units.

£75.00 each

Crankshaft Protector Rod Bolt Boots. This simple pair of rubber boots slides on to the connecting rod bolts when installing the pistons. They protect the crankshaft journals from contact damage when pushing in the piston assembly from the top. Made from soft plastic. Sold in pairs. Suitable for other engines.

£8.00 pair Info

Rocker shaft Transit Screw / Locking Screw Set. This four screw set allows for the locking of the rocker shaft assemblies during engine strip down and assembly. They prevent the rocker shafts flying apart and hold everything in place while working on the engine. Transit screws must be removed prior to running and must not be over tightened. A slight nip is all that is required. An essential item suitable for all Daimler V8 engines.  

£4.50 set of four screws

Engine Lifting Strap. This strap can be used to safely lift your Daimler V8 engine during removal or installation. It is thin enough to feed under and around the intake manifold ensuring a centre point lift position. It is capable of lifting a complete engine and transmission/gearbox assembly safely while keeping the lift height close to the engine alleviating any height restrictions you may have with your crane set up.

£15.00 Strap for 250 SP and Saloon engines £17.00 Strap for 4.5 litre Majestic Major units

Low Profile Engine Crank Socket 3/8DR. This socket allows better accessibility for turning the engine via the crank pulley when setting the tappets or setting the ignition timing. To suit 3/8 square drive ratchet or T’bar. 30mm overall length.

£17.00 each

Cranked Feeler Blades with Handles for Both Inlet and Exhaust Positions. These are the ideal companion for our adjusting spanner (above). A fixed feeler blade and handle of .011” for inlet and .014” for exhaust valve clearance adjustment. Colour coded yellow for inlet and red for exhaust. The feeler blade is cranked to allow easier use with the Daimler V8 setup. No more fumbling around with multi blade sets, just the sizes you need. Sold in pairs.

£38.00 Pair. (1x red 1x yellow.) NEW! Press to Select Cylinder Head Parts Gaskets & Sealing Press to Select Cylinder Block Parts Press to Select Engine Service Press to Select

All prices indicated are correct at time of publication however they may be subject to change without prior notice. All prices are trade price. All parts and tools available over our trade counter or to mail order. Domestic and international shipping and packaging available at additional cost and subject to import duties & local taxes. Thank you for taking the time to look at our Daimler V8 products and tools.

If you wish to place an order for any of our parts, tools or consumables please send an email to: info@250v8.co.uk Please include your full name, shipping address, contact telephone number and of course the items you would like to order. We will raise a free, no-obligation quotation by return email which will include payment instructions should you wish to proceed with the order. Once paid your items will be shipped as detailed in the quotation.

Thank you for your custom

Mail: info@250v8.co.uk?subject=Daimler V8 Parts %26 Tools Enquiry Special Tools Hire Section

D.505 Crankshaft rear oil seal pre sizing tool. Required for correct fitment of the rear crankshaft oil seal packing for all V8 & 250 Saloon engines as well as some very late production SP250. Available for outright sale (See higher up this page) or hire.

Hire £80.00


Postage £15.00


Deposit £280.00


FOR HIRE

Spark Plug Tube Removal and Install Tool. D.506. Churchill designation. This tool is a much improved version of the Churchill design. It allows for simple removal and re-fitting of the cylinder head spark plug tubes without damaging or deforming them. Plug tube removal is required when replacing the seal at the bottom of the tube to prevent oil leaking. Used in conjunction with our modified sealing ring kits or complete tube with integral sealing end. Available for outright purchase (See higher up this page) or hire.

Hire £50.00


Postage £10.00


Deposit £180.00


Automatic Transmission Inhibitor Switch Tool BW547 A-50-3.

A special crows-foot spanner to aid removal of the inhibitor switch on automatic transmission while in situ. For hire only.

Hire £20


Postage £8.00


Deposit £70.00


FOR HIRE

Here you can see our specialist repair tools available to hire. Hire is based on a strict 30 days limit for each tool after which weekly charges will be deducted from your securing deposit. Deposits will be returned on safe return of and un-damage, un-altered tool. Hirer is responsible for postage & insurance costs. Hire tools are only available to UK residents

Or Purchase

Rear Hub Puller Tooll JD.1. Rear hub pulling tool for steel wheel hubs. These can be a real nightmare to remove as the hubs lock onto the halfshaft taper. This tool is available to hire only. A refundable security deposit is required prior to hire. This is refunded on safe return of the tool in an unaltered undamaged state. For STEEL wheels only.


Hire £80.00


Postage £20.00


Deposit £375.00


FOR HIRE

Rear Hub Puller Tool JD.7. Rear hub pulling tool for Daimler V8 & 250 Saloon with wire wheels. One tool suits both left hand and right hand hub threads (Near side & Off side). This tool is available to hire. A refundable security deposit is required prior to hire only. This is refunded on safe return of the tool in an unaltered undamaged state. For Wire wheels only. 52mm x 8TPI.


Hire £60.00


Postage £10.00


Deposit £150.00


FOR HIRE

Oil Pump Alignment Tool. This tool allows for the correct alignment of the oil pump when assembling your engine. This can be seen in the workshop manual although has no special tool designation. The alignment of the oil pump is very important and prevents drive shaft binding in the upper and lower bushes. Incorrect alignment will load the drive shaft which can accelerate wear in the drive gear, bushes and oil pump. Supplied with sliding T-handle.

Hire £35.00


Postage £10.00


Deposit £75.00


FOR HIRE

Rear Hub Puller Tool JD.7(SP). Rear hub pulling tool for Daimler SP250 Dart with wire wheels. One tool suits both left hand and right hand hub threads (Near side & Off side). This tool is available to hire only. A refundable security deposit is required prior to hire. This is refunded on safe return of the tool in an unaltered undamaged state. For Wire wheels only. 42mm x 8TPI.


Hire £60.00


Postage £10.00


Deposit £150.00


FOR HIRE

Hire £60


Postage £10.00


Deposit £125.00


Half Shaft Removal Tool SL.13-2 Rear halfshaft pulling tool for removing the half shafts once the hub has been removed. Suits both steel & wire wheel options. This tool is available to hire only. A refundable security deposit is required prior to hire. This is refunded on safe return of the tool in an unaltered undamaged state.


Or Purchase

Water Pump Pulley Removal Tool for Saloon. Required for correct removal of the water pump pulley from the water pump bearing. To suit both alternator and dynamo pulley wheels. These pulleys can fracture or break very easily if removed with a standard press setup pressing from behind the wheel “You have been warned”. Comes compete with 4x fixing nuts and screw with hardened ball end to prevent galling and bearing damage. Can also be used to adjust the pulley alignment with the dive pulley.

Hire £35.00


Postage £15.00


Deposit £60.00


Water Pump Pulley Removal Tool for Saloon. Required for correct removal of the water pump pulley from the water pump bearing. To suit both alternator and dynamo pulley wheels. These pulleys can fracture or break very easily if removed with a standard press setup pressing from behind the wheel “You have been warned”. Comes compete with 4x fixing nuts and screw with hardened ball end to prevent galling and bearing damage. Can also be used to adjust the pulley alignment with the dive pulley.

NEW! £55.00