Copyright © 2026 J and E Engineering Services Ltd All Rights Reserved

ENQUIRIES (+44) 1706 222662 01706 222662 Telephone Daimler Specific info@250v8.co.uk General Enquiries info@jandeengineering.co.uk

J and E Engineering Services Ltd.

Unit 32 Britannia Mill,

Stoneholme Road,

Crawshawbooth,

Rossendale,

Lancashire.

BB4 8BA.


Monday

Tuesday

Wednesday

Thursday

Friday

Saturday

Sunday

8:30am - 5:30pm

8:30am - 5:30pm

8:30am - 5:30pm

8:30am - 5:30pm

8:30am - 5:30pm

9:00am - 2:00pm

Closed

CONTACT INFORMATION OPENING HOURS VAT Number GB738470805 EORI Number GB738470805000 Company Number 16821373 Websites Main: www.jandeengineering.co.uk Main Alternative: www.j-and-e.co.uk Daimler V8: www.250v8.co.uk Daimler V8: Alternative: www.250v8.com
Home
Rocker Assemblies

Another neglected component within the Daimler V8 engine are the rocker shaft assemblies. There are four in total, 2 inlet and 2 exhaust assemblies. Each Rocker assembly is made up of the following component parts:  

1x Shaft

4x Rocker Arm

5x Alloy Pedestal

4x Spring

12x Thrust Washer

4x Rocker arm adjusting Screw

4x Lock Nut

2x Blanking Plug

1x Dowel Screw

1x Dowel Screw Washer


Number of Components 38 multiplied x 4 Shafts = 152 Individual components

Each of the 152 components requires thorough cleaning inspecting servicing and reassembling so I am sure you can appreciate it is a labour intensive job and perhaps the reason they are often neglected. The problem is that the rocker assembly is a critical part and is subject to high loads & stresses so this should not be the case. It is worth remembering that in order to replace a rocker assembly requires cylinder head gasket replacement as the cylinder head bolts pass through the alloy rocker pedestals. In our experience 90% of all annoying tapping, clicking & clacking noises are down to the rocker shafts. On this page we will look at how we service and rebuild our rocker assemblies.

Rocker shafts are hollow and can bend during removal and/or assembly when aligning the location dowels or freeing from them. Bent shafts will hinder rocker arm free movement and can result in a sticking rocker more so on the exhaust side. The oil blanking plugs must be removed from either end so that the shaft can be cleaned out properly. Each end is then threaded to accept a screw in blanking plug. Shafts are then checked for bend and straightened if required. The shaft is them micro polished and oil drilling holes freed from any burrs.

Rocker pedestals are thoroughly cleaned inspected for cracks and bore checked. It is important to not that the end pedestals of each shaft are different to the others as they have the mail oil feed drilling and threaded hole for the location dowel screw (Stops the shaft rotating) and transit screw (Stops the shaft falling apart during assembly).

Spacer springs are checked for free length, weakness and cleaned. Thrust washers are cleaned then checked for quantity 48 in total. They are easy to loose and it is important that none are forgotten during shaft reassembly.  

2 2

Rocker arms are vapour honed, checked for cracks and internal bore size is measured. The adjuster screw thread is cleaned out (5/16 UNF) and the rubbing pad is re-ground to remove wear and restore the correct radius. It is very important to ensure the oil drilling holes are clear to ensure proper lubrication to the valve tip and push rod cup.

Adjusting screws are removed completely from the rocker arm so that the oil drilling hole can be checked for restrictions. This is a critical part as the oil drilling allows lubrication for the push rod cup and prevents wear. The thread is then chased clean to aid adjustment. Over tightening of the lock nut can stretch the screw and it will become tight in the rocker arm. Rounding of the square drive is also common when the incorrect spanner has been used. Any screws showing this sort of damaged should be replaced.

Rocker Arm Adjusting Spanner

Lock nuts or jam nuts should be replaced if they have rounded out. It is important to remember that the lock nuts for this engine are 7/16” AF and this small size allows just enough room for a spanner when adjusting the valve clearances. Specialist parts companies will supply a new lock nut that is 1/2” AF which is too big and makes tightening the nut more difficult.  Correct size lock nuts are available and can be found here:

New Lock Nuts

During the assembly of our rocker shafts we use Lucas Extreme Pressure Grease on the adjusting screw threads and lock nuts. Before fitting the shafts we also apply a small amount to the valve tips as these parts are under the most pressure during initial start up. The grease offers the best protection in these high stress areas.

6 5 4 1

The transit screws or lock screws are required to prevent the rocker assembly ‘flying’ apart during disassembly and assembly. They are a tool used to assist the engine builder and they must be removed prior to running the engine. They should not be over tightened as a slight nip is all that is required. One screw per rocker shaft is required and we supply them in a set of four.

Rocker Shaft Transit Screws Press to Select Press to Select Press to Select