Engineering

Copyright © 2026 J and E Engineering Services Ltd All Rights Reserved

ENQUIRIES (+44) 1706 222662 01706 222662 Telephone Daimler Specific info@250v8.co.uk General Enquiries info@jandeengineering.co.uk

J and E Engineering Services Ltd.

Unit 32 Britannia Mill,

Stoneholme Road,

Crawshawbooth,

Rossendale,

Lancashire.

BB4 8BA.


Monday

Tuesday

Wednesday

Thursday

Friday

Saturday

Sunday

8:30am - 5:30pm

8:30am - 5:30pm

8:30am - 5:30pm

8:30am - 5:30pm

8:30am - 5:30pm

9:00am - 2:00pm

Closed

CONTACT INFORMATION OPENING HOURS VAT Number GB738470805 EORI Number GB738470805000 Company Number 16821373 Websites Main: www.jandeengineering.co.uk Main Alternative: www.j-and-e.co.uk Daimler V8: www.250v8.co.uk Daimler V8: Alternative: www.250v8.com
Home

Daimler V8 Saloon PAS Crankshaft Pulley Wheel Twin ‘Vee’ Groove C.20974:

Double Vee pulley wheel for driving power steering pump.

Good condition.

Few available.

Rusty.

£75.00

Daimler V8 Saloon Crankshaft Pulley Wheel Single ‘Vee’ Groove C.20973:

Many available.

Crack free.

Good condition.

Rusty.

Daimler V8 Saloon Modified Timing Cover With Oil Seal:

Russ Carpenter modified.

With damper/pulley hub.

As removed from engine.

Good condition.

Actual item shown. Outright sale.

£80.00

Here you will find some some second-hand pre-loved Daimler V8 engine parts we have available. Please check for availability. These second-hand parts are sold as seen without warranty.

Second Hand Parts Daimler V8 Used Engine Parts Press to Select Cylinder Head Parts Gaskets & Sealing Press to Select Cylinder Block Parts Press to Select Engine Service Press to Select

Oil Pump Alignment Tool. This tool allows for the correct alignment of the oil pump when assembling your engine. This can be seen in the workshop manual although has no special tool designation. The alignment of the oil pump is very important and prevents drive shaft binding in the upper and lower bushes. Incorrect alignment will load the drive shaft which can accelerate wear in the drive gear, bushes and oil pump. Supplied with sliding T-handle.

£55.00

Oil Pressure Priming Tool. This tool is inserted through the cylinder block and into the oil pump. It accommodates the use of an electric drill  or wrench to turn the oil pump and generate oil pressure prior to starting your freshly rebuilt engine. Oil pressure can be seen on your in car oil pressure gauge or remote gauge set up. Can also be used for oil pump alignment during assembly and to orientate the oil pump rotor when installing your distributor drive spindle. Universal design ensures use for SP250, Saloon and Majestic Major V8 units.

£75.00 each

Crankshaft Protector Rod Bolt Boots. This simple pair of rubber boots slides on to the connecting rod bolts when installing the pistons. They protect the crankshaft journals from contact damage when pushing in the piston assembly from the top. Made from soft plastic. Sold in pairs. Suitable for other engines.

£8.00 pair

Rocker shaft Transit Screw / Locking Screw Set. This four screw set allows for the locking of the rocker shaft assemblies during engine strip down and assembly. They prevent the rocker shafts flying apart and hold everything in place while working on the engine. Transit screws must be removed prior to running and must not be over tightened. A slight nip is all that is required. An essential item suitable for all Daimler V8 engines.  

£4.50 set of four screws NEW!

Engine Lifting Strap. This strap can be used to safely lift your Daimler V8 engine during removal or installation. It is thin enough to feed under and around the intake manifold ensuring a centre point lift position. It is capable of lifting a complete engine and transmission/gearbox assembly safely while keeping the lift height close to the engine alleviating any height restrictions you may have with your crane set up.

£15.00 Strap for 250 SP and Saloon engines £17.00 Strap for 4.5 litre Majestic Major units

Low Profile Engine Crank Socket 3/8DR. This socket allows better accessibility for turning the engine via the crank pulley when setting the tappets or setting the ignition timing. To suit 3/8 square drive ratchet or T’bar. 30mm overall length.

£17.00 each NEW!

Daimler V8 Saloon Flywheel for Manual Transmission:

Original item

C.27426

104 Teeth

Good ring gear

Good condition / bit rusty.

Rare item.

Actual item shown.

£200.00 Press to Select Cylinder Head Parts Gaskets & Sealing Press to Select Cylinder Block Parts Press to Select Engine Service Press to Select

All prices indicated are correct at time of publication however they may be subject to change without prior notice. All prices are trade price. All parts and tools available over our trade counter or to mail order. Domestic and international shipping and packaging available at additional cost and subject to import duties & local taxes. Thank you for taking the time to look at our Daimler V8 products and tools.

If you wish to place an order for any of our parts, tools or consumables please send an email to: info@250v8.co.uk Please include your full name, shipping address, contact telephone number and of course the items you would like to order. We will raise a free, no-obligation quotation by return email which will include payment instructions should you wish to proceed with the order. Once paid your items will be shipped as detailed in the quotation.

Thank you for your custom

Mail: info@250v8.co.uk?subject=Daimler V8 Parts %26 Tools Enquiry

Daimler V8 Saloon Engine Back Plate:

Good condition.

Many available.

£55.00 £35.00

Daimler V8 Saloon Modified Timing Cover With Oil Seal:

Unknown origins. Similar to our modification.

With damper/pulley hub.

As removed from engine.

Good condition.

Actual item shown. Outright sale.

£100.00